This lab is about 6.4.1.3 Packet Tracer – Configure Initial Router Settings. In this tutorial we will discuss about 6.4.1.3 Packet Tracer answers, in last tutorial we discuss about Introduction to 6.3.1.8 Packet Tracer – Exploring Internet working Devices Instructions.



6.4.1.3 Packet Tracer Answer

6.4.1.3 Packet Tracer - Configure Initial Router Settings
6.4.1.3 Packet Tracer – Configure Initial Router Settings








Here we have topology of 6.4.1.3 Packet Tracer – Configure Initial Router Settings. Equipment’s which we required are as follows

  1. 1 Router
  2. 1 PC

6.4.1.3 Packet Tracer Lab Objective

We have few objectives of this lab which we have to do.

  • Verify the Default Router Configuration

Step 1: Establish a Console cable Connection to R1.

  1. Choose a Console cable from the available connections.
  2. Click PC-A and select RS 232.
  3. Click R1 and select Console.
  4. Click PC-A > Desktop tab >Terminal.
  5. Click OK and press ENTER. You are now able to configure R1.

Step 2: Enter privileged mode and examine the current configuration.

Enter into the Router 1 Privileged mode by the following commands and them examine the current configurations of the router.



Enable the command use to Enter into the privileged EXEC mode.

Router> enable
Router#

Show running-config command is used to examine the current configuration of router.

Router# show running-config

Answer of the following question are as follows

What is the router’s hostname? hostname Router
How many Fast Ethernet interfaces does the Router have? 4 Fast Ethernet Interfaces.
How many Gigabit Ethernet interfaces does the Router have? 2 Gigabit Ethernet interfaces.
How many Serial interfaces does the router have? 2 Serial interfaces.
What is the range of values shown for the vty lines? Line vty 0 4.

Display the current contents of NVRAM.
Router# show startup-config
startup-config is not present
Why does the router respond with the startup-config is not present message?
It displays this message because the configuration file was not saved to NVRAM. Currently it is only located in RAM.

Configure and Verify the Initial Router Configuration

Configure the initial settings on R1.

  • R1 as the hostname.
  • Use the following passwords:
  1. Console: letmein
  2. Privileged EXEC, unencrypted: cisco
  3. Privileged EXEC, encrypted: itsasecret
  • Encrypt all plain text passwords.
  • Message of the day text: Unauthorized access is strictly prohibited.

Verify the initial settings on R1.

  • Verify the initial settings by viewing the configuration for R1. What command do you use? Router# show running-config
  • Exit the current console session until you see the following message:
R1 con0 is now available
Press RETURN to get started.

  • Press ENTER; you should see the following message:
Unauthorized access is strictly prohibited.
User Access Verification
Password:

Why should every router have a message-of-the-day (MOTD) banner?
Every router should have a banner to warn unauthorized users that access is prohibited but can also be used for sending messages to network personnel/technicians (such as impending system shutdowns or who to contact for access).

If you are not prompted for a password,what console line command did you forget to configure?

R1(config-line)# login


Enter the passwords necessary to return to privileged EXEC mode.
Why would the enable secret password allow access to the privileged EXEC mode and the enable password no longer be valid?
The enable secret password overrides the enable password. If both are configured on the Router, you must enter the enable secret password to enter privileged EXEC mode.

If you configure any more passwords on the router, are they display in the configuration file as plain text or in encrypted form? Explain. The service password-encryption command encrypts all current and future passwords.

Save the Running Configuration File

Step 1: Save the configuration file to NVRAM.

You have configure the initial settings for R1. Now back up the running configuration file to NVRAM to ensure that the changes made are not lost if the system is rebooted or loses power.

What command did you enter to save the configuration to NVRAM? copy running-config startup-config

What is the shortest, unambiguous version of this command? copy r s

Which command displays the contents of the NVRAM? show startup-configuration or show start


Verify that all of the parameters configured are recorded. If not, analyze the output and determine which commands were not done or were entered incorrectly. You can also click Check Results in the instruction window.


Although you will be learning more about managing the flash storage in a router in later chapters, you may be interested to know now that —, as an added backup procedure —, you can save your startup configuration file to flash. By default, the router still loads the startup configuration from NVRAM, but if NVRAM becomes corrupt, you can restore the startup configuration by copying it over from flash.
Complete the following steps to save the startup configuration to flash.
Examine the contents of flash using the show flash command:
R1# show flash

How many files are currently store in flash? 3 files
Which of these files would you guess is the IOS image? file number 3
Why do you think this file is the IOS image? file number 3 contain c1900-universalk9-mz.SPA.151-4.M4.bin

Save the startup configuration

Save the startup configuration file to flash using the following commands:
R1# copy startup-config flash
Destination filename [startup-config]
The router prompts to store the file in flash using the name in brackets. If the answer is yes, then
press ENTER; if not, type an appropriate name and press ENTER.
Use the show flash command to verify the startup configuration file is now stored in flash.

Hamza Arif
Follow us

Hamza Arif

Hey, i hamza arif student of telecommunication from BZU, i am good in Networking, Telecommunication and Web Development working on different projects and try my best to teach them to all of you.
Hamza Arif
Follow us

One thought to “6.4.1.3 Packet Tracer – Configure Initial Router Settings”

Leave a comment

Your email address will not be published. Required fields are marked *