7.2.4.9 Packet Tracer - Configuring IPv6 Addressing

7.2.4.9 Packet Tracer answers

This lab is about 7.2.4.9 Packet Tracer – Configuring IPv6 Addressing. In this tutorial we will discuss about 7.2.4.9 Packet Tracer answers, in last tutorial we discuss about Introduction to 6.5.1.3 Packet Tracer – Skills Integration Challenge.











 

Objectives

We will perform the objectives of lab for CCNA R&S 7.2.4.9 Packet Tracer-Configuring IPv6 Addressing. Following objectives will be performed for securing 100% marks in Lab for CCNA R&S.

  1. Configure an IPV6 addressing scheme on the Router.
  2. Configure an IPV6 addressing scheme on the Servers.
  3. Configure an IPV6 addressing scheme on the clients.
  4. Test and verify the network connectivity


Part 1: Configure IPv6 Addressing on the Router

Step 1: Enable the router to forward IPv6 packets.
  1. Enter the ipv6 unicast-routing global configuration command. This command must be configured to enable the router to forward IPv6 packets. This command will be discussed in a later semester.

For performing the lab for CCNA R&S 7.2.4.9 Packet Tracer-Configuring IPv6 Addressing following commands and steps should be completed.

R1(config)# ipv6 unicast-routing

Step 2: Configure IPv6 addressing on GigabitEthernet0/0.
  1. Click R1 and then the CLI tab. Press Enter.
  2. Enter privileged EXEC mode.
  3. Enter the commands necessary to transition to interface configuration mode for GigabitEthernet0/0.
  4. Configure the IPv6 address with the following command:

R1(config-if)# ipv6 address 2001:DB8:1:1::1/64

  1. Configure the link-local IPv6 address with the following command for the lab of CCNA R&S 7.2.4.9 Packet Tracer-Configuring IPv6 Addressing:

R1(config-if)# ipv6 address FE80::1 link-local

  1. Activate the interface.
Step 3: Configure IPv6 addressing on GigabitEthernet0/1.
  1. Enter the commands necessary to transition to interface configuration mode for GigabitEthernet0/1.
  2. Refer to the Addressing Table to obtain the correct IPv6 address.
  3. Configure the IPv6 address, the link-local address and activate the interface.
Step 4: Configure IPv6 addressing on Serial0/0/0.
  1. Enter the commands necessary to transition to interface configuration mode for Serial0/0/0.
  2. Refer to the Addressing Table to obtain the correct IPv6 address.
  3. Configure the IPv6 address, the link-local and activate the interface.


Part 2: Configure IPv6 Addressing on the Servers

Step 1: Configure IPv6 addressing on the Accounting Server.
  1. Click Accounting and click the Desktop tab > IP Configuration.
  2. Set the IPv6 Address to 2001:DB8:1:1::4 with a prefix of /64.
  3. Set the IPv6 Gateway to the link-local address, FE80::1.
Step 2: Configure IPv6 addressing on the CAD Server.

Repeat Steps 1a to 1c for the CAD server. Refer to the Addressing Table for the IPv6 address.



Part 3: Configure IPv6 Addressing on the Clients

Step 1: Configure IPv6 addressing on the Sales and Billing Clients.
  1. Click Billing and then select the Desktop tab followed by IP Configuration.
  2. Set the IPv6 Address to 2001:DB8:1:1::3 with a prefix of /64.
  3. Set the IPv6 Gateway to the link-local address, FE80::1.
  4. Repeat Steps 1a through 1c for Sales. Refer to the Addressing Table for the IPv6 address.
Step 2: Configure IPv6 Addressing on the Engineering and Design Clients.
  1. Click Engineering and then select the Desktop tab followed by IP Configuration.
  2. Set the IPv6 Address to 2001:DB8:1:2::3 with a prefix of /64.
  3. Set the IPv6 Gateway to the link-local address, FE80::1.
  4. Repeat Steps 1a through 1c for Design. Refer to the Addressing Table for the IPv6 address.


Part 4: Test and Verify Network Connectivity

Step 1: Open the server web pages from the clients.
  1. Click Sales and click the Desktop tab. Close the IP Configuration window, if necessary.
  2. Click Web Browser. Enter 2001:DB8:1:1::4 in the URL box and click Go. The Accounting website should appear.
  3. Enter 2001:DB8:1:2::4 in the URL box and click Go. The CAD website should appear.
  4. Repeat steps 1a through 1d for the rest of the clients.
Step 2: Ping the ISP.
  1. Open any client computer configuration window by clicking the icon.
  2. Click the Desktop tab > Command Prompt.
  3. Test connectivity to the ISP by entering the following command:




PC> ping 2001:DB8:1:A001::1

  1. Repeat the ping command with other clients until full connectivity is verified and the lab for CCNA R&S 7.2.4.9 Packet Tracer-Configuring IPv6 Addressing is completed successfully.


You should also practice the lab for CCNA R&S 7.2.4.9 Packet Tracer-Configuring IPv6 Addressing. Stay tuned for further labs for CCNA R&S which will prove you helpful in Cisco Certifications.

 

 

Hamza Arif
Follow us

Hamza Arif

Hey, i hamza arif student of telecommunication from BZU, i am good in Networking, Telecommunication and Web Development working on different projects and try my best to teach them to all of you.
Hamza Arif
Follow us

2 thoughts to “7.2.4.9 Packet Tracer – Configuring IPv6 Addressing

Leave a comment

Your email address will not be published. Required fields are marked *