7.3.2.5 Packet Tracer – Verifying IPv4 and IPv6 Addressing

7.3.2.5 Packet Tracer answer

Hi today we are going to perform the lab for CCNA R&S 7.3.2.5 Packet Tracer – Verifying IPv4 and IPv6 Addressing. If you feel difficult to understand you can see the video down below. You may also see the 7.2.4.9 Packet Tracer – Configuring IPv6 Addressing





Addressing Table

Ipv4 and Ipv6 addressing table for 7.3.2.5 Packet Tracer – Verifying IPv4 and IPv6 Addressing

Objectives

Part 1: Complete the Addressing Table Documentation




Part 2: Test Connectivity Using Ping

Part 3: Discover the Path by Tracing the Route

Background

Dual-stack is the technique used in lab for CCNA R&S 7.3.2.5 Packet Tracer – Verifying IPv4 and IPv6 Addressing allows IPv4 and IPv6 to coexist on the same network. In this lab for CCNA R&S 7.3.2.5 Packet Tracer – Verifying IPv4 and IPv6 Addressing, you will investigate a dual-stack implementation including documenting the IPv4 and IPv6 configuration for end devices, testing connectivity for both IPv4 and IPv6 using ping, and tracing the path from end to end for IPv4 and IPv6.



Part 1: Complete the Addressing Table Documentation

Step 1: Use ipconfig to verify IPv4 addressing.

We will perform the following steps for lab of CCNA R&S 7.3.2.5 Packet Tracer – Verifying IPv4 and IPv6 Addressing.

  1. Click PC1 and click the Desktop tab > Command Prompt.
  2. Enter the ipconfig /all command to collect the IPv4 information. Fill in the Addressing Table with the IPv4 address, subnet mask, and default gateway.
  3. Click PC2 and click the Desktop tab > Command Prompt.
  4. Enter the ipconfig /all command to collect the IPv4 information. Fill in the Addressing Table with the IPv4 address, subnet mask, and default gateway.
Step 2: Use ipv6config to verify IPv6 addressing.

Now we will use the ipv6config /all command for lab of CCNA R&S 7.3.2.5 Packet Tracer – Verifying IPv4 and IPv6 Addressing.

  1. On PC1, enter the ipv6config /all command to collect the IPv6 information. Fill in the Addressing Table with the IPv6 address, subnet prefix, and default gateway.
  2. On PC2, enter the ipv6config /all command to collect the IPv6 information. Fill in the Addressing Table with the IPv6 address, subnet prefix, and default gateway.



Part 2: Test Connectivity Using Ping/

Step 1: Use ping to verify IPv4 connectivity.

We will use the Ping command for IPv4 to verify the connectivity for lab of CCNA R&S 7.3.2.5 Packet Tracer – Verifying IPv4 and IPv6 Addressing.

  1. From PC1, ping the IPv4 address for PC2. Was the result successful? Yes
  2. From PC2, ping the IPv4 address for PC1. Was the result successful? Yes
Step 2: Use ping to verify IPv6 connectivity.

We will use the Ping command for IPv6 to verify the connectivity for lab activity of CCNA R&S 7.3.2.5 Packet Tracer – Verifying IPv4 and IPv6 Addressing.

  1. From PC1, ping the IPv6 address for PC2. Was the result successful? Yes
  2. From PC2, ping the IPv6 address of PC1. Was the result successful? Yes




Part 3: Discover the Path by Tracing theRoute

Step 1: Use tracert to discover the IPv4 path.

We will use an appropriate command for tracing the route using IPv4 address for lab of CCNA R&S 7.3.2.5 Packet Tracer – Verifying IPv4 and IPv6 Addressing.

  1. From PC1, trace the route to PC2.

PC> tracert 10.10.1.20

What addresses were encountered along the path? 10.10.1.97, 10.10.1.5, 10.10.1.10, 10.10.1.20

With which interfaces are the four addresses associated? G0/0 of R1, S0/0/0 on R2, S0/0/01 on R3, NIC of PC2

  1. From PC2, trace the route to PC1.

What addresses were encountered along the path? 10.10.1.17, 10.10.1.9, 10.10.1.6, 10.10.1.100

With which interfaces are the four addresses associated? G0/0 of R3, S0/0/1 of R2, S0/0/1 of R1, NIC of PC1

Step 2: Use tracert to discover the IPv6 path.

We will use the tracert command for IPv6 address to find the IPv6 path for lab of CCNA R&S 7.3.2.5 Packet Tracer – Verifying IPv4 and IPv6 Addressing.

  1. From PC1, trace the route to the IPv6 address for PC2.

PC> tracert 2001:DB8:1:4::A

What addresses were encountered along the path? 2001:DB8:1:1::1, 2001:DB8:1:2::1, 2001:DB8:1:3::2, 2001:DB8:1:4::A

With which interfaces are the four addresses associated? g0/0 of R1, S0/0/0 of r2, S0/0/1 of R3, NIC of PC2

  1. From PC2, trace the route to the IPv6 address for PC1.

What addresses were encountered along the path? 2001:DB8:1:4::1, 2001:DB8:1:3::1, 2001:DB8:1:2::2, 2001:DB8:1:1::A

With which interfaces are the four addresses associated?  Ga0/0 of R3, S0/0/1 of R2, S0/0/1 of R1, NIC of PC1

Stay tuned for more Packet Tracer solved labs for Cisco Certifications.

You may also see the VoIP Phone Configuration – VoIP call Quality

Hamza Arif
Follow us

Hamza Arif

Hey, i hamza arif student of telecommunication from BZU, i am good in Networking, Telecommunication and Web Development working on different projects and try my best to teach them to all of you.
Hamza Arif
Follow us

One thought to “7.3.2.5 Packet Tracer – Verifying IPv4 and IPv6 Addressing”

Leave a comment

Your email address will not be published. Required fields are marked *